Tool:Launch X431 V,LAUNCH X431 V+,etc. 

Module：2009 Land Rover Discovery 3，VIN：SALAN25489A50****；

Function：When finding DTC in ABS steering angle or replaced some parts，

need to use this function.

Operation：

Choose “Intelligent diagnostic”，confirm all the information.

Choose “Quick test”；

Choose “SASM”；

Choose “Special function”；

Choose “ABS Steering angle calibration”；

Prompt: Make sure the steering wheel is in the middle and the front wheel

is directly in front；

Prompt: Switch on the ignition(Position 2)；

Prompt: Please wait；

Press “Yes”；

Prompt: Steering wheel angle sensor calibration finished；

Press “Yes”；

Prompt: Turn off the ignition (Position 0) ；

Prompt: Switch on the ignition (Position 2) ；

Prompt: Turn off the ignition (Position 0) ；

Prompt: Please check all the DTC；

Function finished.

List most Launch X431 Pro3 Frequently Asked Questions.

1. Error -5 (new adapters)
Most likely your device uses the new security and work with it just do not happen, but you can try the following system:
1). If you should roll back its firmware 11.54 to version 11.52 (as flashing the adapter, see the section №4)
2). Turn off the Internet connection on the tablet / computer
3). Start the original application EasyDiag LAUNCH
4). Perform the connection to the vehicle via any program, for example OBD2TOOL (this is necessary to initialize the adapter)
5). Close the original application EasyDiag LAUNCH
6). Run PRO application
7). Perform n Connecting to the vehicle
– Use the brand until June 2017.
– On some adapters “focus” can not ride in this case is to use only original software

2. When you run any program there is a message ?Realy Quit?
– It is necessary to update the adapter firmware is flash read in paragraph №4

3. Stamps are downloaded with an empty license file (LICENSE.DAT = 0 KB)
1). Try to install the application and download the brand through:
– For EasyDiag: easydiag.apk (26.19 MB Download now)
– For MDiag: m-diag.apk (27.09 MB Download now)

2). Sign up on the website and download the LAUNCH brand from-to:
mycar. x431.com

3). apply power to the adapter, run the original application, the Internet on your tablet / smartphone must be turned on after connecting with the adapter program to overwrite the normal size of the license file

– If you have bought a new device and none of the above does not help feel free to contact provider apparatus with a claim to idle yc roystvo

4. How to flash adapter

To update the firmware on the shell X431 Pro3S 3.10.020 You will need:
1). Download the correct firmware: Archive of firmware (2.22 MB Download now)
2). Copy the firmware to your tablet / smartphone at
?cnlauncn / X431Pro3S / 968 ******** * / the DIAGNOSTIC / the Configure / Download ?
3). In? Download ?will be based on two files? Download.bin ?and? download.ini ?folder
4). Launch X431 Pro3S application
5). The application, press Menu -> About -> firmware Restoration software
6). In the menu Restore firmware, press the red button “Restore firmware”
– Before the beginning of the firmware, check the charge battery on your tablet / phone
– If the firmware procedure on the adapter must be powered
– 968 ********* is the serial number of your adapter
– An example is given for the shell Launch X431 Scan Tool Pro3S 3.10.020, in other shells path to the firmware file may be different

5. When you start the brand message Disaccording between the software serial No and smartbox serial No ….
Possible causes:
– Not a patch applied correctly
Invalid license file –

6. The shell does not see brands
Possible causes:
– Stamps copied down the wrong path , for example: for the shell X431 Pro3S 3.10.020 way for brands to be next:
cnlauncn / X431Pro3S / 968 ********* / DIAGNOSTIC / VEHICLES

In VEHICLES folder must lie folders trademarks, AUDI, BMW, RENAULT, etc.

– ********* folder 968 with the serial number of your device
– a folder cnlauncn be radically your tablet / smartphone filesystem

7. The computer does not see when connecting cnlaunch folder
1). Copy the folder cnlaunch to the SD card directly from the device using any file manager, eg Total Commander, then copy from the SD card to a computer
2). Create a copy of the folder cnlaunch directly from the device using any file manager, eg Total Commander, when it uses the new folder name, a new folder will be visible from your computer
3). Add cnlaunch folder to the archive directly from the device using any archiver, for example RAR, an archive will be visible to the computer
4). The most reliable method. Install the plug-in for Commander of Total All Android the ADB and work with the root file system of your device without restrictions

8. PRO application does not run on your phone / tablet, the original application is working properly
– Please update your smartphone / tablet firmware (on some devices do not start never)
Most becproblemnye smarfony / tablet – Samsung

On obd2tool.com. We have some new arrival tools such as Autel MaxiCOM MK808, MaxiCheck MX808, Autel MaxiCom MK808TS and Maxicheck MX808TS. Many clients are confused about them, what are the exact difference of MX808 and MK808? what is the difference of MK808 and MK808TS, etc. Today we share a list for you to explain the detail difference among them.

First. I need to tell you something very important

1. MaxiCOM MK808 = MaxiCheck MX808

they have the same functions and same supported vehicle models. The difference between them is MX808 is only English Version, MK808 supports multiple language. they have the same functions and same supported vehicle models.

2. MaxiCom MK808TS =MaxiCheck MX808TS
they have the same functions and same supported vehicle models.

3. MK808BT= MK808+Bluetooth

Second, let’s figure out the difference of MK808/ MX808 and MK808TS/ MX808TS and MK808BT

Are Autel Scanner any good?

Autel Maxidas DS808. Last but not least, the Autel MaxiDAS DS808 is one of the best selling Autel scan tool models, and it’s very reliable. This is a scanner designed for professional use and comes with lots of features. It has specialized functions like cloud-based MaxiFix, Smart AutoVIN, and Shop Manager Functions.

What Nissan Consult 3 Plus?

Nissan Consult 3 is a diagnostic software special for Nissan,support all the models of the Nissan and Infiniti from 1996 up till now, with all Consult II & III functions.It can support all Nissan car,Infiniti carand Nissan GTR.

Nissan Consult 3 Plus Functions List:

Supports ECM reprogramming on most 1999 model year and later and some TCM and ABS/VDC reprogramming.

Supports blank ECM and TCM programming.

Supports ECM reprogramming on most 1999 model year and later and some TCM and ABS/VDC reprogramming.

Supports blank ECM and TCM programming. September 2013 Nissan and Infiniti began the phase-in of “blank” service part ECMs and TCMs. Depending on the model and model year, replacement modules come WITHOUT software. When the replacement module is installed in an applicable vehicle for any reason, it will need to be programmed.

Optional Security Card-Type A Kit must be approved security professional to purchase

Nissan Consult 3 Plus Specifics:

PC Based: PC Require

Model Year Coverage: The Consult-III Plus is required for all 2013 and newer Nissan and Infiniti vehicles. In addition, the Consult-III Plus is required for all: 2011 and newer Nissan LEAF, Quest, and Murano CrossCabriolet vehicles; 2012 and newer Nissan GT-R and NV vehicles; and 2012 and newer Infiniti M and M Hybrid vehicles. The Consult-III Plus software is continuously being updated to accommodate new vehicles as well as older model years dating back as far as 1996.

PC Recommended: Nissan Specific, Panasonic Toughbook

Software License:https://www.nissan-techinfo.com/

Nissan Consult 3 Plus Support Car Models:

Diagnostics:for all Nissan,Infiniti,GTR
Immo and Smart key:for all Nissan,Infiniti,GTR
Nissan GTR: for Nissan GTR Diagbostics and Immobi
Electromobiles car:for Nissan Electromobiles car Diagbostics and Immo

Nissan and Infiniti from 1996 up till now
Note:Consult III Plus – 1996MY up

Nissan Consult 3 Plus Support Languages:

English, Portuguese (Newly Add), French, German, Spanish, Italian, Japanese, Russian, Finnish, Greek, Chinese(Simplified), Chinese(Traditional)

Nissan Consult 3 Plus Installation OS Requirement:

Operating System Environment

*   Windows: Windows® 2000, Windows XP, Windows Vista, Windows 7, 8 or 8.1
*   Mac: Macintosh 8.x, 9.x, OS X
*   Disk Storage: 10 MB available hard-drive space
*   Display Resolution: 800 x 600 pixels (1024 x 768 recommended)

Nissan Consult 3 Plus Installation Guide:

The installation methods of different Consult 3 may be similar,if there here is no version that you have or you have higher version,please try to install it referring to these method by yourself.

How to Install Nissan Consult 3 III Plus Diagnostic Software

Nissan Consult 3 Plus Free Download:

Nissan consult 3+ plus V83.11.00:

https://mega.nz/#!D9ZRnaSL!Y6rksoTqF1rbpx2-tIvliYFN5RcQSb6s-WwKqBGByZI

Nissan Consult 3+ Plus V81.11.00

https://mega.nz/#!ukhgRSYJ!DXM22QAbQDo-b4Di9e6tyxy2SE4fKVogLmKCv6QzZUA

Nissan consult3 plus V75.20 free download:

https://mega.nz/#!WYYmiQ6J!QDCblZBomUBfEkTUEHd9ZCHWzV0cUKM-_3fT0nW7scg

Nissan Consult 3 Plus V72.13 free download

https://mega.nz/#!EVBC1I6a!mwvSkwf4SKqBN0oYDAhpvWJNFPHdWSKHKGaKgXknkSw

Nissan Consult 3 Plus V71.11.00 & 71.20.00 from 05.2017

https://yadi.sk/d/GsZoo_VD3KxqER

How to Reset BMW ELV when battery registration failure?

Problem:
it’s already happened to one of you that you can’t register the new battery with ista? and the steering lock light in yellow lights up, it’s impossible to reset the elv.

Solution:
E Model you can use NCS (you find Battery Capacity in cas) ELV you can use tool 32 (please open cas.prg)

If you only changed battery with the new one with the same capacity, then do this:
*Tool32:
SGBD: (Choose DME or DDE) “Steuren_batterietausch_registri Start job once
If you changed the capacity or type: *Change E-word in VO of the car by NCSEXPERT, write FA and code CAS
Alternatively use esys for F serie and code CAS/FEM
Then try to reset ELV counter and CAS in ISTA or Tool32 .
loading..

Problem:

I had error when programming BMW F32 in ISTA-P 4.19.13 Expert Mode.

Error:

Vehicle programming with ISTA/P is no longer approved for the connected vehicle.
Vehicle management is now only possible with ISTA-D.

*Before version ISTA 4 it was called ISTA/D (aka Rheingold).
It would cover diagnosis on all cars.
Beginning from version 4 its called ISTA+.

Obd2tool.com Solution:
The error indicates that  BMW F, I, G series programming is not available in ISTA-P (since version 4.19.xx), but in ISTA+ instead.
From version 4, besides diagnosis it also covers programming of F series.
and ISTA/P is left for programming of E series only (therefore ISTA/P can not program F series anymore).
Here’re tips to set up programming in ISTA+ ( Rheingold or ISTA-D).
Run ISTA+ software, identify vehicle
Then choose Service Plan
(click to enlarge images)

Choose Programming Plan

Then Execute measures plan

Follow ISTA prompts to carry out programming.

The latest BMW ICOM ISTA+ goes to 2020.03 ISTA-D 4.21.30
loading..

Problem:

I had error when programming BMW F32 in ISTA-P 4.19.13 Expert Mode.

Error:

Vehicle programming with ISTA/P is no longer approved for the connected vehicle.
Vehicle management is now only possible with ISTA-D.

*Before version ISTA 4 it was called ISTA/D (aka Rheingold).
It would cover diagnosis on all cars.
Beginning from version 4 its called ISTA+.

Obd2tool.com Solution:
The error indicates that  BMW F, I, G series programming is not available in ISTA-P (since version 4.19.xx), but in ISTA+ instead.
From version 4, besides diagnosis it also covers programming of F series.
and ISTA/P is left for programming of E series only (therefore ISTA/P can not program F series anymore).
Here’re tips to set up programming in ISTA+ ( Rheingold or ISTA-D).
Run ISTA+ software, identify vehicle
Then choose Service Plan
(click to enlarge images)

Choose Programming Plan

Then Execute measures plan

Follow ISTA prompts to carry out programming.

The latest BMW ICOM ISTA+ goes to 2020.03 ISTA-D 4.21.30
loading..

MB SD Connect C4 C5 C6 newest version software is V2020.02.03

Please kindly note :

1.Including Super Engineer Software: DTS monaco V8.14.016 And Vediamo V5.01.01 Support Offline Programming

2.Support Wireless

3.Software Version: V2020.03

HardwareVerison:OS:2.3 CSD:2.11

4.Support Multi-Language: (Default language is English, if you want other languages, please leave message)

English/Bulgarian/Danish/Greek/Spanish/French/Italian/Korean/Polish/Romanuan/Serbo-Croatian/Turkish/Czech/German/Finish/Hyngarian/Japanese/Dutch/Portuguese/Russian/Swedish/Chinese.

5.Support Both Mercedes Benz Cars and Trucks

6.Support Mercedes Benz Cars After Year 2000

7.Support Offline and Online Programming, If You Want to Do Online,you must have an account online. Buy This Online SCN Coding Service

MB Star C4 C5 C6 Softwares list:

1. DAS 2020.03: the automatically Diagnosis Assistance System
2. Xentry 2020.03: New software released by Bennz Company after 04/2009 by diagnosis new cars.
3. WIS net 2019.07:Workshop Information System

Supply the whole view of the wiring diagram in a car, component location diagram and maintenance method. What you do is to enter the chassis number, and then you will get the manufacture data, engine configuration and the car model -all in detail.

4. EPC.net 2018.11:Electronic Parts Catalog
5. ST Finder:Part Location Finder options: 2008 and 2016
6. STARUTILITIES :the movement management system and self-test
7. SD MEDIA 2014
8. PL73

9.HHT Software for old cars

10.Engineer version Vediamo updated to V5.01.01 ，Engineer version DTS updated to V8.14.016，Upgrade to the latest version of 2019 data

1) Fix the error that Mercedes-Benz DAS cannot directly call WIS

2) Join the DAS sedan smart offline programming

3) Join the 204 DAS stand-alone version, which can be mutated (German), which is more powerful than Vediamo

4) Join DAS special function password-free access PKW and SMART

5) Repair SMART 450, 451, 452, 454 No longer need TAN Caculator, all offline

6) Increase offline EOL and VMAX all LKW, modify truck maximum speed limit

7) Lift the truck NOx TORGUE restriction, do not need FDOK XT calculation code, directly enter, directly cancel the legal speed limit, you can modify without special function

8) Clear the truck SCR/ADBLUE fault code (MR), do not need FDOK XN calculation code, enter directly

9）Add DAS 212，207 prototyp model

10）Add Xentry special features and the VeDoc calculator($53 for activation)

MB SD Connect Compact software display:

OBDSTAR Odo Master Odometer Correction Tool is latest OBD mileage change tool launched by OBDSTAR which is based on OBDSTAR X300M. It has a wide vehicle coverage of Ford, from 2005 to 2019.

Take Ford Focus for example:

Here is the detailed Ford carlist:

This test report feedback from our customer real test project,he use this new product Autel MaxiIM608 to read PIN code for Dodge smart key.

Operation Procedures:

Connect Autel Scan Tool IM608 to vehicle,then enter menu to select “Dodge”

Select “Smart Mode”

Turn the ignition on

If it is old pre 2006 model,please give priority selection to “Manual Selection” or “System Selection”!

Establishing vehicle communication

Select “knob-style smart card”

Switch the ignition off and then on again,make sure the engine off.

Establishing vehicle communication…

Switch the ignition off and then on again,make sure the engine off.

Establishing vehicle communication…

Then you will get the PIN code:8095