New Super MB STAR C6 is coming! Compare with the old MB star M6, it supports programming & coding on BMW F/ G series cars and DOIP protocol for more than Mercedes.

1.Interfaces

 
SUPER-MB-STAR-C6-DOIP-WIFI-Diagnostic-Tool-Full-Version-2
SUPER-MB-STAR-C6-DOIP-WIFI-Diagnostic-Tool-Full-Version-3

2.Highlights
1.The new SDconnect C6 is able to work for DoIP.
2.It’s the only C6 that supports ethernet communication (DoIP).
3.Have tested no issues on the new Mercedes with DoIP.
4.No need to worry about firmware damage during the update process
5.The wireless connection is stable. (With built-in Wifi Chip)
6.remote help is available.
7.Good Quality, It’s waterproof, shockproof, and tamper-proof.
8.With Free DTS Monaco & Vediamo
9.Support both 12V Cars and 24V Trucks.
10.not only supports K line diagnosis and CAN BUS, but also UDS diagnose protocol.
11.Connector adopt Military quick swap technology, it can support 10,000 times pull the plug, more stable;
12.All core accessories adopt the original new packing chip, and a 24hours test, guarantee the quality of the products.

Softwares list:
1. DAS 2023.03: the automatically Diagnosis Assistance System.Support 213/257 and so on new cars to register free to diagnosis
2. Xentry 2023.03: New software released by Bennz Company after 04/2009 by diagnosis new cars.
3.WIS net 2021.07: Workshop Information System
Supply the whole view of the wiring diagram in a car, component location diagram and maintenance method. What you do is to enter the chassis number, and then you will get the manufacture data, engine configuration and the car model -all in detail.
4. EPC.net 2018.11: Electronic Parts Catalog
5. ST Finder: Part Location Finder options: 2016 and 2020 and 2022
6. STARUTILITIES: the movement management system and self-test
7. SD MEDIA 2014
8. PL76 2022.01
9.HHT Software for old cars
10. Engineer version Vediamo updated to V5.01.01, Engineer version DTS updated to V8.16.15，Upgrade to the latest version of 2021 data
1) Fix the error that Mercedes-Benz DAS cannot directly call WIS
2) Join the DAS sedan smart offline programming
3) Join the 204 DAS stand-alone version, which can be mutated (German), which is more powerful than Vediamo
4) Join DAS special function password-free access PKW and SMART
5) Repair SMART 450, 451, 452, 454 No longer need TAN Caculator, all offline
6) Increase offline EOL and VMAX all LKW, modify truck maximum speed limit
7) Lift the truck NOx TORGUE restriction, do not need FDOK XT calculation code, directly enter, directly cancel the legal speed limit, you can modify without special function
8) Clear the truck SCR/ADBLUE fault code (MR), do not need FDOK XN calculation code, enter directly
9）Add DAS 212，207 prototyp model

MB SD Connect C6 Software Functions:
1.1989~up to now Car, Bus, Truck, Sprint, Smart ;
2.All electric system Diagnostic;(Do not include flash code)
3.reading trouble code
4.erasing trouble code
5.live-data
6.adaptation
7.component testing
8.maintenance
9.information consultation
10.component location diagram
11.wiring diagram

Testable systems:
ENGINE
AUTO-SPEED
AIRCONDITIONAL SYSTEM
SRS
ABS
ASR
MPL
GM
Bz ORIGINAL ANTI-THEFT
DASX SYSTEM
KEYZESS GO SYSTEM
OBD-II SYSTEM

MB SD C6 Supported Vehicle List:
Passenger Car Support List:
A(176), A(169), A(168), B(246), B(245), CLC(117), C(204) C(203), C(202), 190(201), E(212), E(211), E(210), 124(124), S(222), S(221), S(220), S(140), S(126), E(207), CLK(209), CLK(208), CLS(218), CLS(219), CL(216), CL(215), CL(140), SLK(172), SLK(171), SLK(170), SL(231), SL(230), SL(129), SL(107), SLS(197), M(166), M(164), M(163), G(463), G(461), E(212), E(211), E(210), 124(124), S(222), S(221), S(220), S(140), CLK(209), CLK(208), CLS(218), CLS(219), CL(216), CL(215), CL(140), SLK(172), SL(231), SL(230), SL(129), SL(107), SLS(197), M(166), M(164), M(163), G(460), GL(164), GLK(204), R(251)

Van Support List:
MB 100(631), T1, SprinterIII, SprinterII, SprinterI, Sprinter900, Citan, Vito(639), Vito(638), V(638), Viano(639), T2, Vario, Vaneo(414)

Truck Support List:
Actros963/4, Actros2,3, AtegoIII, AtegoII, AxorII, Eonic, Zetros, Actros, Atego Light, Atego Heavey, HPN M96, Atron, HPN M2000, SKL, FSK, Further model series

Unimog Support List:
U20, UGN, UHN

Bus Support List:
TRAVEGO, INTOURO, INTEGRO, CITARO, CAPACITY, CITO, TOURISMO, O350/ O403, CONECTO, O404, O405- O408, Minibus, OC500, TOURO, TOURINO, MBC, MULITEGO, O500, O500/ OH, OH, OH368, OF, OF384, LO, O400, FURTHER MODEL SERIES

Super Sports Car Support List:
SLR(199)

You must read the warnings and instructions which are contained in the safety section of this manual. Before you perform any operation or maintenance procedures ensure you understand the warnings and instructions.

Caterpillar ET 2023A & 2019C Electronic Technician Diagnostic Software

Check Condition

1. Park the machine on level ground. Fully retract the boom and lower the boom.

2. Remove the cover from the rear of the chassis.

3. A limited inspection of the chains can be made through the rear of the boom. The boom extension chain can be inspected by fully extending the boom and looking on top of the intermediate section. If the chains are corroded, the chains must be removed from the boom for cleaning and a full inspection. If the chains require lubricant, the chains must be removed from the boom for cleaning and a full inspection. Refer to the Hydraulic System Systems Operation, Testing and Adjusting, “Boom Chain – Clean/Inspect/Lubricate”or consult your Caterpillar dealer

4. Set the minimum distance to 224 mm (8.8 inch) between boom section 2 and boom section 3. The maximum allowable distance is 234 mm (9.2 inch). Tighten extension chain (1) in order to move section 3 outward. Tighten retraction chain (2) in order to move section 3 inward. If the distance is significantly more than 224 mm (8.8 inch), slacken both chains and refer to Step 1.

5. After setting the distance to the required tolerance, tighten the extension chain to 20 N-m (15 lb ft).

6. Tighten the retraction chain to 18 N-m (13 lb ft).

7. Tighten the extension chain to 105 ± 5 Nm (77 ± 4 lb ft).

8. Tighten the retraction chain to 70 ± 5 Nm (52 ± 4 lb ft).

9. Extend the boom and retract the boom several times. Check the torque for the extension chain. Check the torque for the retraction chain.

10. Install the locknut for the extension chain. Torque the locknut for the extension chain to 105 ± 5 Nm (77 ± 4 lb ft).

10.2021 Caterpillar SIS EPC+Service Manual download & Full Installation Service

11. Install the locknut for the retraction chain. Torque the locknut for the retraction chain to 70 ± 5 Nm (52 ±
4 lb ft).

12. Check the shackles on both chains. If necessary, adjust the shackles in order to set the shackles horizontally.

13. Remove the stand and lower the boom.

Best Quality 2023A/2019C CAT Caterpillar ET 3 Diagnostic Adapter III CAT Truck Diagnostic Tool PLUS Panasonic CF19

This instruction show you guide on how to use Launch X431 IMMO to add a new key for Porsche Cayenne 2011-2017. For more repair case about Porsche,please refer to:Porsche Cayenne Repair Cases.

Device Requires:

LAUNCH X431 IMMO

Procedures:

Select “Porsche”à”Anti-Theft Key Matching”à”CAYENNE”à”2011-2017”

Please follow the picture to build connection:connect to the immobilizer programmer G3,and click “OK”

Click “Read immobilizer data”

Select “5M48H”à”View the wiring diagram”

Connect the ECU and G3 programmer according to the wiring diagram.The amount of data is large.

To improve communication stability,use the USB cable to connect the tablet and the Bluetooth connector.

Click “Back up EEPROM data”

Input file name to store in on your X431 device (here file name eep)

Now back to menu to select “Generate dealer keys”

Place new key you want to add to G3 programmer slot

Select the EEPROM data file you read before (name eep)

Select unused location to generate new key

Generate new key successfully

Now back to select “Learn Keys”

Now here you need re-match all key

Here select the eep file read before again

Input the number of keys to be match:2

Insert new key and switch to ON

Then it will ask you to match second PC,just do same steps

After then matching completed.

More test report about Launch X431 please check:Launch X431 Test Report